Re: w1-gpio not working on Pi Zero W
Quote from: DrRob on June 11, 2017, 01:17:41 PMmodprobe: can't load module wire (kernel.tclocal/drivers/w1/wire.ko): unknown symbol in module, or unknown parameterThat message means that wire.ko is...
View ArticleRe: Steps to connect a Pi Zero W to wifi
Quote from: DrRob on June 11, 2017, 01:11:05 PMfor pkg in ca-certificates libiw libnl ncurses openssl readline wifi wireless-4.9.22-piCore wireless_tools wpa_supplicant firmware-rpi3-wireless; do for f...
View ArticleRe: Which board to support?
Hi Béla,I just started an other thread to discuss the pros and cons of getting tinycore on the new Asus Tinker Board.Sorry I did not see this thread , TinkerBoard was not mentioned in any post...
View ArticleClik here to view.
Re: can't access TCE from USB
Quote from: tcFan on June 12, 2017, 03:59:08 PMI did a frugal install and it bootsAnother symptom is that when I try to ls the usb drive, I can't do it without sudo. But permissions seem correct..I...
View ArticleRe: iptables log location?
You need to use the "syslog" boot code to get /var/log/messages
View ArticleRe: cannot run laptop-mode-tools
I guess you need to modify /usr/local/sbin/laptop_mode to read something like this: Code: [Select] case "$KLEVEL" in "2.4" ) ;; "2.6" ) ;; "3.0" ) ;; "3.8" ) ;; "3.16" ) ;; "4.2" ) ;; "4.8" ) ;; *)
View ArticleRe: iptables log location?
..and you also need to have a LOG rule set for iptables to log anything.
View ArticleRe: VT8237A/VT8251 No Sound
^ true, anyways, in order to save ALSA settings, the commendCode: [Select]sudo alsactl storeis always required to be ran before backup + reboot/shutdown, for the config file to be updated so the...
View ArticleRe: VT8237A/VT8251 No Sound
Quotesudo alsactl store is always required to be ran before backup + reboot/shutdown, for the config file to be updated so the settings can be restored after reboot.Sure you can take that route if it...
View ArticleRe: VT8237A/VT8251 No Sound
I didn't know ALSA is unreliable when it comes to restoring its settings. Maybe because I'm not a Linux kid for too long, yet.A few TC versions back, this was needed for me in bootlocal.sh[code][ -e...
View ArticleRe: cannot run laptop-mode-tools
laptop-mode-tools adjusted and reposted in tc-4.x x86 repo
View ArticleError saving writer document libreoffice 5
HelloAfter updating Libreoffice from 4 to version 5 I get an error by saving writer documents. >Error saving the document Untitled1:Write Error.The file could not be written.>It is funny a...
View ArticleRe: Blank/black screen after wake-up?
There is a suspend-utils in the tc-4.x x86 repo, but I don't know how useful this would be with a more modern kernel.
View ArticleRe: Blank/black screen after wake-up?
Quote from: Juanito on June 14, 2017, 11:59:30 PMThere is a suspend-utils in the tc-4.x x86 repo, but I don't know how useful this would be with a more modern kernel.Thanks again. Are you saying that...
View ArticleRe: Blank/black screen after wake-up?
Video related suspend issues are very common on Linux.
View ArticleRe: gpm under VTs half-dead?
] which version of corepure64 are you using - 8.x?I only tasted V8; reluctant to change from a working system: V7.] Are you using the corepure64 gpm extension or gpm from somewhere else?gpm.tcz...
View ArticleRe: haproxy
Hi AdamThis extension announcement was for TC2. The TC4 repository contains the same extension as it was originally released.Seeing as it has no dependencies, you could try downloading it...
View Article